Performance Boats Forum banner

tab

  1. V-Drives
    Does anyone make a timing tab for one of these style covers?
  2. Parts for Sale
    1 - Place diverter or trim up and down steering control switch new never opened... 1 - Billet up and down place diverter or trim steering wheel control switch new never used or installed $ 55.00 each plus ride if needed Located in Murrieta Ca. (951) 440-7200
  3. Parts for Sale
    I just bought a set of Eddie marine trim tabs and I need the mechanical indicator and the cables, possibly the switches too Email [email protected] or call (509)430-7733 Steve I do not care if they are a different brand
  4. Outdrives
    Didn't see any other place to post this so I'll ask here. I've been looking at lots of pictures of used boats with trim tabs. It looks like some are mounted such that the bottom of the plates are horizontal and some are mounted at at the same angle as the V in the bottom of the boat. So I'm...
  5. Parts for Sale
    I need a controller, any style as long as it would work with Bennet wiring harness.
  6. GN7 On the Dyno
    Anybody try one of these ?
  7. Outdrives
    What's the difference on setup. Some angled some straight. Always wondered if it would be worth the investment on my cheetah. Would I want them over the tunnel or outside the tunnel. What the benefit of one over the other. How would it help at upper speeds? Thanks
  8. Jet Boats
    Looking for pics of trim tab setups. I going to be building a set for my 18ft stwd, any pics would help. Thanks
  9. User "How To" Section
    I am looking at adding some trim tabs for my 24 foot Ultra Stealth. I am running a stock 496 MAg HO, Bravo 1 X drive with a Bravo 1 26 prop in the low to mid 70's (72/74). For my application I am just trying to get rid of some chine walk and stabilize the ride of the boat at higher speeds. Any...
  10. Greg Shoemaker
    I am looking at adding some trim tabs for my 24 foot Ultra Stealth. I am running a stock 496 MAg HO, Bravo 1 X drive with a Bravo 1 26 prop in the low to mid 70's (72/74). For my application I am just trying to get rid of some chine walk and stabilize the ride of the boat at higher speeds. Any...
  11. V-Drives
    Just bought a 1986 21' Hallet V-Drive Daycruiser and the trim tabs don't work. I was able to get the tabs to go down slugishly and then couldn'g get them to come up at all. I took the actuator apart and it looked corroded and I think I may have damaged it while disassembling. I was wondering...
  12. Paint and Fiberglass Repair
    I have a few nicks on the upper drive casing paint and the rams that actuate the tabs. Id like to touch them up with the right paint/enamel. What paint or other substance should I use to touch this up? Thanks! Uncle Dave
  13. PB Open Water
    Hey Guys, I was wondering if you guys know how difficult AND how expensive it would be to install Trim Tab indicators on my 23' Renegade. I already have the Dana LT-500 Trim Tabs installed but have no indicator panel, so it would just need the indicator panel (plus hardware) installed. I was...
  14. Jet Boats
    My neighbor has a jet boat with the typical porpoising problem. He only is a recreational boater. He does not want to work on the bottom of his boat or spend the money on a place diverter. Boat is all stock 75 Sanger Super Jet with a stock olds. Can he just install a set of cast trim tabs, the...
  15. Parts for Sale
    Dana center sponson tab, If you want to cut your plane time , have mid range and top end controll, this is for you the tab is designed for twin motor cats up to 29' it is a dual ram set up 12 wide by 28 long it has never been mounted, and comes complete with all hard ware. pump, switch, rams...
  16. Gary Taylor
    It seems that the current thought in performance (stepped) V-Hulls is to mount the tabs parallel to the hull and as close as the drives to tabs clearance will allow. Is this still the case? What other factors are there to consider? What other advice might there be? I'm tired of the 30 Victory...
  17. PB Open Water
    You bet! :)violent11
Top