Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 71 Results
  1. Parts for Sale
    Rex liquid filled temp gages $50 shipped $50 shipped
  2. V-Drives
    Just wanted to update anyone that was interested , i run a bbc and had the glenwood 1 inch pump that caused the motor to never get warm and i changed the housing to the 3/4 housing after getting very good advice from alot of people on here and it worked perfect!!! thank you to everyone who...
  3. V-Drives
    quick question , I was using a 1 inch magnaflow pump and the motor never got warm, maybe 120 degrees running on the trailer,,,long story short I got the 3/4 pump housing and was told to keep an eye on the temp because the 3/4 was made for small blocks and the 1 inch for big blocks, and theres a...
  4. GN7 On the Dyno
    I only have a oil psi gauge , I would like to put a temp gauge during the winter, the issue is I know they should be in the oil pan , I have a canton oil pan that has 2 drain bungs, problem is I cant use the second oil drain (long story and not my fault:D seriously) so where is the next best...
  5. Races and Boating Events
    I built a temp site that has the race ladders from this weekend.
  6. Jet Boats
    I am totally lost...I have a medalian water temp gauge that isn't giving me a reading. I took the sensor wire off...grounded it, and the gauge spikes, no problem. I have replaced the sending unit from a GM truck (same as I always ran)...and reading at all. Where do I look next?
  7. Parts for Sale
    I'm looking for a good Accu-Com Oil Temp Gauge with a White face to match what I already have. Hope someone can help
  8. Parts for Sale
  9. Delta Lunch Bunch ( dlb )
    Sounds like a boat ride is in order!!:)devil
  10. Parts for Sale
    Great condition. AutoMeter lite gauges in satin brushed aluminum color. 3-3/8" Tach, and 2-1/16" size Oil Pressure-Mechanical, and Temp-Mechanical $100 for the set. Chris
  11. GN7 On the Dyno
    I`m running a BDS intake with no thermostat provisions, what options do I have to build some heat in the motor?
  12. Parts for Sale
    cobalt water temp gauge,long sweep, mechanical. brand new, too short to reach for my boat dash. 916-616-6833 paul
  13. Bob Teague
    Hello, I have a Sanger flatbottom v-drive with a 327 Chevrolet 1960's engine and Rewarder wet headers. It is run in freshwater only. I bought the boat this summer. When i went to winterize this fall there was no thermostat. I am in Michigan. Is thermostat needed and if so what temp. I tried a...
  14. V-Drives
    Hello, I Have a 327 Chevy in a v drive. When i went to winterize there was no thermostat. Is one needed and if so what temp? Thanks
  15. GN7 On the Dyno
    I am having an issue with getting the temp up on the motor. I have a 556 with aluminum dart heads, bravo outdrive, merc pump, with the Harden Marine crossover kit. The kit comes with a 140* thermostat but i am only building temp up to 100*. I put in a mechanical gauge just to see if my in dash...
  16. PB Open Water
    Thinking about going out the weekend of October 25th- 27th - can anyone tell me what the water temp is currently? Lake River Thx
  17. Parts for Sale
    *********Mechanical fuel gauge ----------------------------------------------------------------------Steve @ 760-390-0736----------------------------------------------------------------with gauge monnt
  18. Jet Boats
    Looking to install a temp gauge. Pan has bung so that's a no brainer. Is there a certain type or manufacture I need to look for? I was planning on using this SW. Mechanical of coarse.
  19. Outboards
    I have a 1995 2.5 liter XRi 150 and I've been searching for information on proper operating temperature. Mine currently fluctuates between 140-170 degrees depending on RPM. I've never had an alarm sound, is 170 too high? Is this normal? I boat in the lower colorado river, air temp have been 105+...
  20. Parts for Sale
    I have a new still sealed Auto Meter Sport-Comp 2 5/8 Mechanical Water Temp gauge that I can't use. They sell for $79.97 at Summit Racing but I will take $50.00 for it plus the ride or trade for a good electrical version of the same size & style. Or, if someone has a good electrical version for...
1-20 of 71 Results