Performance Boats Forum banner
testing
1-20 of 92 Results
  1. Delta Lunch Bunch ( dlb )
    Hey N,P, I was talking to a couple of whacker guys( these guys are fast) who run those 10 hp merc hurricanes and they said you should get away from those, 3 blade aluminum and try some of these new 2 blade brass, they even said there is this new thing, they called it cupping thing that they do...
  2. V-Drives
    she did really good........
  3. V-Drives
    Come on out....you know the drill, safety in numbers. White Trash is gassed up! Jocko PS....come on out Dwight Ivy!! lol!! :wink2:
  4. V-Drives
    Didn't get time to cut that one prop down, but will still be testing 3 props for an 1-1/8" shaft and 1 prop for a 1" shaft. If you have a flat and want to try these props too, you're more than welcome. Gonna be done by 1-2 pm ish. Jocko
  5. V-Drives
    Chris Donahue brought out his nice Cole TR1 today. He got several good runs in until the Santa Ana winds kicked up. Had a great visit with him and his son and his friends from Denmark. He'll be back for the NYD event and recruit a few other flats as well! Great day, Jocko
  6. V-Drives
    We want to test our race boat at Lake Elsinore tomorrow. Is there rangers or anyone that will hassle us because its a race boat? Any help would be great.
  7. V-Drives
    Took out Kurtis runner yesterday, Has 18s and 11 1/8 16 Minkins, it ran 80 MPH on one of the runs.not sure which one. one video is 6 seconds 6500 RPM. I did not want to go any faster with my Son on board. I'm sure it will go to 7,000 it's stilling pulling hard. Blower Had 12% under drive 7 lb...
  8. BOTE
    Changed my mind.
  9. V-Drives
    anybody ever heard of sonic testing to check for rotten stringers, floor etc?
  10. Boats for Sale
    Giving thought to selling my M29, twin 300 outboards. 30 hours, extended Merc warranties until 6/17. Always stored indoors at Lake Powell. Carbon fiber, Kevlar, Penske composite, vacuum bagged, full cap. Extreme triple axle 20" wheels, galvatube construction, clear bra on front rails, rear...
  11. V-Drives
    My brother saw alot of race boats this week at elsinore a gn and a flat and a cracker diff days practiceing for long beach he said he talked to one of the owners at a gas station and the guy said irvine lake is no more..sold it or something..he said new owner has no inerest in letting the race...
  12. V-Drives
    Did a little testing last weekend in Parker, trying to get this thing ready after some bad luck things are finally looking up! Hope u all dig it. Sorry about quality but it is what it is.
  13. West Coast - North
    I don't know where everyone else is located, but I live in Selah, WA and there are a lot of lakes in the area, none that is really very close. There is one spot near here that has a two-mile stretch of slow to moderate current on the Yakima River that is a couple of minutes away and easily...
  14. Jet Boats
    Want to test your boat on the water? Irvine Lake is offering you gearheads a chance to test on Wednesdays between 4 p.m. and 7:30 p.m. One boat at a time may be tested, and a flotation device must be worn. Cost is $50 per boat. Call Tina at the office at Irvine Lake at (714) 649-9113...
  15. V-Drives
    FYI: TESTING AT IRVINE LAKE HAS BEEN SUSPENDED UNTIL FURTHER NOTICE. THANK YOU.
  16. Delta Lunch Bunch ( dlb )
    Presidents Day Prop Testing We are going to Orwood today around noon to run the Vector and try the new Grose Racing Prop. Anyone else have the day off?
  17. V-Drives
    ...Just testing...Tried to delete couldn't... ...The original contents of this have been moved to the test section of the RDPForums... ...Here is the link... ...Testing 1...2...Testing 1...2...
  18. Jet Boats
    Since i got the boat finnished, i have had it out twice and i have had no reading on the water temp gauge. An electrical guru I am not. So i was wondering if someone could tell me how to properly test the circuit? This is the situation. While running the boat each time, i have idled thru no wake...
  19. Jet Boats
    testing
  20. GN7 On the Dyno
    I have a Race Aero twin turbo set-up and wish to pressure test the radiators. I am looking for the best way to pressure test it and find out if there is any leakage. Since I have never had intercooler apart, I think it is in my best interest to ask those who have. The engine is currently being...
1-20 of 92 Results
Top