Search Results for ‘throttle’

Nicson foot throttle , floor mount, free shiipng ​SOLD NICSON FOOT THROTTLE WITH 8ft CABLE V-DRIVE OR JET BOATS Floor Mount, Polished, Excellent Condition $180.00 FREE SHIPING to CA, NV, AZ Call 530 575 5025

I have a "Hall-craft" stringer mount throttle pedal assembly (restorable condition - pedal & mount only - no cable) asking $50.00 plus the ride. Call lynn @ (626) 375-4286 (voice only).

looking for a offset pedal mount, anyone have one they will part with? I have the pedal assembly just need the offset mount. thanks!

I just got my new motor in and went to put on the throttle cable and is either to long or short. I can adjust the cable mount, but the it still wont line up. Is the adjustment at the carb end or in the pedal end? At the carb end I have the barrel that slides onto the ball on the carb. There are...

i have a 76 Sutphen Jet boat with a stuck throttle and pump cable...can not push the lever forward only backward... Any advice to lubricate (which I hope would free the cables) would be helpful since it does not have a cable but a steel rod that slides back and forth (I think) thanks...

i have a 2200 CFM throttle body for use with Muli-port injection. it has the TPS and Iac sensors on it and throttle linkage . asking 400 bucks it's the Raw/polished finish and looks like it's new or almost new.. excellent shape. i can not use this in the car im building and forced to buy a lower...

Looking to find what throttle cable bracket to get for my push style pedal / cable setup. Going from a stock BBC intake and Edelbrock carb to a Edelbrock Victor Jr. with a Holley 850. Attached are pics of the existing bracket which is clearly not tall enough once I attach the linkage to the top...

I am replacing the throttle cable on my 21 Daytona and I can't seem to locate a cable end that connects to the Nicson gas pedal. The old adapter has a 10/32 female thread on one end and a 5/16" hole in the other. Through all my internet research, I haven't been able to find a replacement. I'm...

single throttle control with trim button and 2 16ft cables with adapters 300$ shipping included

New to the forum so be nice :) Outboard is 6 cylinder with carburetors Has 300 hours Cranks fine but when small amount of gas applied in gear it dies. Had very similar problem a few years ago except you could apply some throttle but with aggressive throttle it would stall; replaced primer bulb...

Anyone have any experience with this? I can get a good deal on the full kit with the fuel system. I'm currently running an over-bored & custom 2 barrel TBI with qty (2) injectors on my 454. MEFI 1 ecu old skool tech... I know the thing isn't getting enough fuel and air, wanted to stay injected...

Jegs Scoop mount and Throttle Mount Assy. w/ Return Spring. For A 4150 Carb Pattern (Non Dominator) $100.00 I will pay Shipping 951-318-1998

Brand new MSF stringer mount throttle pedal setup. $300 contact Nick @ 626-786-7779.

!979 SKV Day Cruiser with 5.7 liter MerCruiser and Alpha outdrive. Throttle works fine (running or not) out of water but in water it is hard to go from reverse to forward. I adjusted the linkage once when it would go into forward but not reverse. any suggestions?

I must be mission something or I have the wrong bracket. There are two main issues: 1. The bracket does not line up with the carb linkage. The angle of the cable is too much, It may work but I don't like having the throttle cable angle that drastic. 2. It hits the front accelerator pump. I can...

Not sure what the regulations are, but I'm a believer. Push the linkage over centre just once and a good day will go south. Seems to be a regular question, how to make one. This is what I came up with today as I was mounting the gas pedal in my Flat. All aluminum parts with stainless steel...

single throttle control with trim button and 2 16ft cables with adapters 300$ shipping included

Anyone have a base plate throttle cable holder with clip for a std. Holley?

Matching Glenwood Marine throttle and cavitation plate return pedals, including spring, shifter and threaded rod. All in very good condition. Used for 3 seasons. $450 plus shipping or best offer.

Looking for a Dominator throttle plate if anyone has an extra.. any help? Ken