Performance Boats Forum banner
tight
1-15 of 15 Results
  1. Jet Boats
    I just replaced my cable and the steering is still very tight. Has anybody switched from the stock Berkeley thru hull fitting to this one and it helped the steering cable always stay lined up with no pressure put on it? CP Performance - Steering Cable Support - Splashwell Mount i have the place...
  2. PB Open Water
    OFFSHORE powerboat sewer run https://www.youtube.com/watch?v=ZJoBLgE5_Kg
  3. V-Drives
    So I'm doing a pre-season freshen up on the Bezer and strut bushings were on the list. Pulled the old ones out, knocked in some new ones in and the shaft fit is pretty tight. Normally I like the bushings snug but I can push the prop shaft in with my foot. With these I had to tap it in with a...
  4. PB Open Water
    Hi everyone, New to the forum. I am Travis, and I have a 2007 aftershock 283. I hope you might be able to help, and hope the is the right section. We were driving home from havasu to Phoenix today and I noticed my hatch was bouncing up and down about an inch at highway speeds. It is operated by...
  5. Jet Boats
    I am installing a new PTO and driveline on my boat. Anybody know the torque setting for the bolts attaching the PTO to the flexplate? How about the bolts for driveline to the PTO? I assume I should use locktite on both. Red or Blu locktite? Thanks
  6. V-Drives
    Hi all, So I'm working on my '73 Stevens... Rebuilt a trailer for it, stuck it on and am now replacing the oil pan on the engine and doing some other "need to fix" things while it's down and out. So the last time I was out, I hit some rough water and to make a long story short, I broke the...
  7. PB Open Water
    50' Maruader w/3x1075's
  8. PB Open Water
    Hey Everyone! Just edited up footage from last weekend of the race in Port Huron, Michigan. It was a great site and the US and Canadian officials are working hard to make it even better and more established next year! Enjoy! AMSOIL #77 Dominates Inaugeral Pt. Huron Race - YouTube PS Some of...
  9. Jet Boats
    Long story just went through my jet, time to put the impy in and I would have swore I had heard on here a few weeks prior someone said to set em at 010. Long story short lookin at another wear ring thread on a different board got my curiosity up and the berk manual says .025 - .035. I don't mind...
  10. PB Open Water
    Tight Squeeze Ahead Boys! http://
  11. GN7 On the Dyno
    Pulled the crank today, going to replace the rod bearings, figured might as well since it looked like junk ran through them and i still had things apart. I noticed that some rods move very easy, the pins will slide back and forth and let the rod move around easy. Then i have 3 pistons/rods...
  12. PB Open Water
    http://www.carolinajournal.com/exclusives/display_exclusive.html?id=5081 its starting already, Dems want your 401K's
  13. V-Drives
    I came across this while looking for parts and just thought I would pass it along, looks very clean and the price seems very fair to me but then again what do I know :)sphss...
  14. PB Open Water
    Both teams are starting to heat up for the stretch run. I'm hoping big Adam Dunn can offset Sloppy ManRam. The race is on. GO D-BACKS:D NSF
  15. Jet Boats
    Woke up the boat from winter hibernation. Found the steering very tight, had to muscle with 2 hands to drive the boat. Seems like there is a inch or 2 of play before you feel resistence. I lubed the zerk on the steering just above the pump outside the boat before we went out. Do I need a new...
1-15 of 15 Results
Top