Performance Boats Forum banner


  1. Wts 3m 5200 10oz tube (new)

    Parts for Sale
    I have a 10oz tube of 3M 5200 Adhesive Sealant White Un used, Un opened I used one tube to adhere rubber pads to my new 25 gallon gas tanks and have this new unopened sealed in it's shipping bag Extra 15 bucks + ride Call 530 575 5025
  2. CMI big tube headers

    Parts for Sale
    CMI big tube headers / tail pipes IMCO mufflers $5500.00 + shipping
  3. Eng. Parts CMI big tube headers

    Parts for Sale
    CMI big tube headers / tails / mufflers / clamps gaskets & transom trim rings. $5500.00 Blower shop intercooler + belt Dyno time only $1350.00 Custom built blower belt cover $250.00 + shipping. Contact Joe 412-551-4354
  4. looking for vdrive driveline tube

    I'm looking for drive line tube 5 1/4 X 24". Does anyone have any suggestions.
  5. WTB Big tube CMI headers (2.375)

    Parts for Sale
    WTB Big tube CMI headers with tails
  6. [SOLD] driveline tube 2 pc $60

    Parts for Sale
  7. Manta Ray Kite Tube

    Other Stuff for Sale
    Manta Ray Kite Tube for the extreme tuber, Check them out on you tube Very Rare. $650 + any shipping
  8. CMI big tube headers

    Parts for Sale
    SOLD! CMI big tube headers I have a set of CMI big tube headers with stainless lines, freshly polished and pressure tested. asking $1800 jonathan 951-538-2115 text for pics they are to big for this site
  9. WTB 16"long by 3" tube oil cooler

    Parts for Sale
    Howdy from Houston! Looking for a engine oil cooler 16" end to end, 3" tube diameter, with 1" water in & outs and 1/2 NPT oil holes. Thanks in advance. The mounting brackets would help as well...:wink2: 713-384-5197
  10. Steering tube installation

    Jet Boats
    Soooo, how exactly, is this suppose to be installed? Baught it from Marine Industries West, but no installation instructions came with and I can't find any thing online about it.
  11. 3 Gallon Polished Moon Tank with ice tube

    Parts for Sale
    Approximately 3 gallon Moon tank with ice tube and Mounts in pretty good shape. A couple minor dings and scratches and one mounting foot is cut off. $200.00. 505-228-8221 Jeff
  12. Driveshaft and tube for sale

    Parts for Sale
    Driveshaft tube...decent chrome..17" length... 7 1/4" OD....$75. Driveshaft...1350 flanges...12" to 13 1/2" length....$75. plus shipping from 77351....thanks...Don.
  13. Wanted: Drive Line Tube and supports

    Parts for Sale
    Looking for a drive line tube and the supports for a circle boat application. Driven off the snout.
  14. Anybody out there doing mobile tube bending?

    Delta Lunch Bunch ( dlb )
    I need a roll cage built onsite. Just measure out and bend all the tubes and Ill weld them in. tube size is 1-3/4" x .134" wall mild steel tubing
  15. [SOLD] SBC Gil Long Tube Headers

    Parts for Sale
    Gil long tube chrome headers for a SBC. The headers have baffles installed. Water lines are included with the sale. There is some blueing on the chrome that will likely clean up with some polish. I received these with a boat I just purchased so I have not run them personally. Buyer will pay...
  16. 1970's Glenwood Torque Tube Guard

    Parts for Sale
    NOS Polished Glenwood Torque Tube Guard Brand New $115 Call or Text Tim 508-902-8528
  17. MANTA RAY ski tube question.

    PB Open Water
    Does anyone have any experience, good or bad, using this tube. I have access to the use of one and wondering how it worked out. I heard some lakes have banned the use of them. thanxs David
  18. [SOLD] CMI Tube Headers SBC

    Parts for Sale
    I have two sets of CMI tube headers with tails. Retails is $4k for these without the tails. $2500 each pair. Full stainless. $4k for both pair. Sacramento
  19. Brand new CMI split tube headers

    Parts for Sale
    Brand new CMI split tube headers, great for a twin turbo set up $1600 for both sets they are new never ran! a hard find! call 252-six four six-2751
  20. dipstick tube question

    Jet Boats
    May be a stupid question but does anyone know if the stock 455 Berkley pack-a-jet had a mounting bracket on the dipstick or if the tube itself had a compression fitting on it? Ive been doing some research for one and I keep coming across these compression fit tubes. any thoughts?