Search Results for ‘turbo’

hey how about few pictures of your engine setup with turbos, especially if they are under the hatch need some inspirations for BBC 502-560 ci I'm caught up with practicality of going with Rajay E13 wheels with water jackets or actually wanting to run a larger twin turbo or single BW 80mm wheel...

Does anyone know or have a 3 inch thick spacer (alum or tubing) to lengthen an exhaust log manifold so the turbos line up from side to side? Perhaps Banks makes one? I know only one brand is set up that way but not my Edelbrocks. Help

Water jacketed tailpipes for Gentry turbo exhaust housings. Came off of a v-drive 21’ Schiada River Cruiser with a Race-Aero system. 27” long, some scratches, need to be repolished, one tailpipe has four or five dings. $200. Pick up Long Beach, CA. Five62 eight5eight 6ninetwo6.

Like New 21 pitch three blade performance prop, Mid sized gear case like 70 to 150 hp range, works great near the surface. asking $275 obo Thanks Dropping price to $225

redoing a 78 daytona jet, twin turbo 6.0, holley EFI

Approx 108.000 miles clean title 17 inch MOMO wheels recent new tires 1.8 turbo 5 speed manual with short throw shifter. turbo boost kit pop off valve boost gauge, average 28 miles per gallon needs minor cosmetics. runs very strong. has left cv boot torn. asking 3750.00 obo. would be a great...

SOLD 8 new low impedence Precision 225's. They were installed and idled. No run time at all. $975 Its a great deal. Pick up 3 lakes area Miami Fl or + shipping. These are a $1440 set of injectors. 918 two six nine 8084

Dirt Cheap Price For These headers. Heavy wall 304 stainless turbo headers by Shearer Fabrications. 3/8" flanges and 1/2" threaded T6 turbo mounts 1 7/8 tubes. They are new. Engine was started and idled. These are 3X the quality of stainless works and ebay headers dont even come close. They...

Turbo components from Corky Bell turbo kit. $1,200

New/unused Lee Performance Products stainless turbo headers with wastegates. Headers are water cooled and made for Garret T4 tangential turbine housings. Wastegates have 1.5" diameter valve. $7,000 Also available are Lee Performance Products small block Brodix aluminum cylinder heads with...

Turbos and Wastegates SOLD Headers $2,200 Procharger valve $400 Wilson elbow and Accufab 90mm TB with TPS $300 Best of Everything! No E-bay Components here. No run time, idle time only. 2 Inch 304 stainless turbo headers by Shearer Fabrication. 3/8 flange 1.600 x 1.860 ports. They are a work...

WTB Turbo 400 WTB - Looking for Turbo 400 transmission. Anything out there?

Just picked up a 78 19 Daytona jet, going with a twin turbo LS(been racing a Turbo LS drag car for years). Have a couple of questions, what oil pan are you using ? the pump is set way back so nothing under engine, also the BB in this was way forward(to me) 30.5" transom to rear plate, 14"...

Gentry twin turbo hat goes on top of T/ram base, possible intercooler Been hanging on to it However have PFM and Gale Banks setup nice polish job can post to USA from Australia whats it worth?

Looking for exhaust tips for Gentry Turbo housings similar to those in pic.

Twin turbo kit minus a few parts. Don't know a lot about it. looks in good shape. Selling for a friend. $1,500 Albert 626-419-7317 Will be in Parker this weekend

Twin Turbo BBC - fresh, complete NEW PRICE For Sale: 468 Twin Turbo Big Block Chevy. 468 cubic inch, twin RayJay turbos. Balanced rotating assembly. Dual fresh Holley 750cfm carbs (matched), Dooley scoops with spark arrestors. All machine work performed by Gary Kincaid @ Showtime Marine in...

Would trade for a street rod, muscle car RUNNING the wife and I can drive around Florida. This engine is fresh. Started not ran. Complete Engine And Turbo System minus intake manifold fuel and ignition system $10,500 Dry Sump, Gear Drive, Shaft Rockers, Billet Caps, Pac Springs, Straub Cam...

Well, after about 5 years of on again off again work, this boat is finally back on the water. 1980 center steer drag hydro we bought out of a field. We reglassed the floor and stringers, plugged every extra hole in the stringers, and covered that with a layer of Kevlar. Then we filled the dash...