Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 32 Results
  1. V-Drives
    LOOKING FOR A RUDDER CHECK WITH LYN (PIE)YOUNG ON HERE AND JJ BEAVERFAB FOR A WHIRLAWAY CLICK HERE........... @ (626) 966-7713 and leave me a message AND CONTACT JJ HERE.......... Company...
  2. V-Drives
    serious question for a biesmeyer flat, crank snout drive. I want to hear pro's and con's and why. Kinda hoping a few of the racers will toss out the info!.
  3. Parts for Sale
    Looking for used good condition whirlaway for a casale....1 INCH shaft. thanks.
  4. Parts for Sale
    whirlaways for casale v-drives 3 new available - i have 3 new whirlaways for casale v-drives.....$600 each or $1500 for all 3 text nine five one 870-69ten text is best dont always answer....or email will work [email protected] PM ME ON HERE CHECK DAILEY casale v-drive vdrive flatbottom...
  5. V-Drives
    To change the release direction, am I right in thinking you have to buy new dogs and change them?
  6. V-Drives
    I am going to run in River Racer next year with my Buck Smith flat. I have a Hallcraft v-drive. I just running a 425 HP 402 BBC and I'm told I don't have to install a whirlaway. But I think it might not be a bad idea. Anybody know where I might find a whirlaway for a Hallcraft, are they common...
  7. V-Drives
    New Pro Whirlaway Housing Our Pro Whirlaway housing replaces your Whirlaway Spacer and Shift Box when running a clutch or transmission for a clean look while using standard whirlaway gears. Made from beautifully machined 6061-T6 aluminum that is approximately 5 3/4" long. Fits a standard 6...
  8. V-Drives
    I have casale v-drive with a whirl-away on it but I think its going to only release if the prop shaft was to spin right hand. The motor is in back wards, driving off the fly wheel going in to the v-drive. If I hold the input shaft and try to spin the prop shaft to the left it wont release,but if...
  9. Parts for Sale
    Complete 12* Casale box with whirlaway.In good shape. Was rebuilt and has low hours on V drive and whirlaway. $1000.00 Thanks Mark 310-629-2503
  10. Parts for Sale
    Looking for a set of whirlaway dogs 10 spline left hand for a casale
  11. Parts for Sale
    Looking for a 10 Degree Casale split case with or without whirlaway.. gears would be nice around 18% .. for a project im putting together .. so post up or pm me or call .. 530-333-1047 Bill kinda on a budget so not looking to spend Alot so nothing New please or high dollar
  12. Parts for Sale
    10 degree Casale with prop release, 1.12, 1.18 and lightened 1.22 gears. Very nice set of s/s tanks (seen in photo), sprint car type steering setup, Throttle pedal with cable, complete cav plate set up........oh hell I'll throw in the boat and trailer if you buy the parts for $4K. No engine...
  13. Parts for Sale
    Looking for a six bolt spacer for casale whirlaway thanks eddie
  14. Parts for Sale
    Looking for a Stellings/Argon prop release.
  15. Parts for Sale
    Almost new 10 degree Beaver V-Drive with mid plate and whirl-a-way. 1" out shaft with New coupler (SOLD) $1800.00. Also have a New 11x16 1" Menkens prop $400.00, Brodix HV2001 intake with 1050 Dominator $850.00, Two Pro Billit MSD's 1 new $185 and 1 used (SOLD) $125 and a couple of cams and...
  16. V-Drives
    Can anyone give info on this release unit? coggs need replaced anyone used one of these for V-drive?:shock: Are they still available and rebuildable? If I remember right this came offf of a hondo runner bottom. Wanting to use it on a shovelnose hydro.....OOOH who made them? still running them?
  17. V-Drives
    How much for new spraggs? or to rebuild the setup? Also cost to assemble a 12 degree Casale with 1 in output shaft (I have new bearings gaskets with 25 gears) needing assy only.
  18. Parts for Sale
    Looking for used good condition whirlaway for a casale 12 degree box......1 INCH shaft. Please let me know what you got. Its for my Shovelnose hydro:happy:
  19. Parts for Sale
    Casale v-drive gearbox. disassembled....This is a RIGHT HAND BOX off a Hondo circle boat....Been disassembled too long so will need bearings and gaskets..everything else in good shape...Has RIGHT HAND Whirlaway, 1 1/4" splined input shaft with hub..., 1' output shaft, in-and-out...
  20. V-Drives
    How much are these Kits? Shelfo can you pm me for assembly cost?
1-20 of 32 Results