Performance Boats Forum banner

1 - 20 of 34 Posts

·
Premium Member
Joined
·
762 Posts
Discussion Starter #1
So a couple of years ago my brother, kettle 1 decides he wants a boat for himself, so I found him a pretty nice 94 cp that had a decent motor and some pump work. Boat worked great for a couple of years and would do about 84 mph at our local Tuesday night deal. During regular maintenance last fall,discovered that a valve lock was about to pull thru the retainer, so, we decided its a good time for some aluminum heads, cam, but wait, since we are here we might as well do this, that ,etc. You have heard this story before right!!

Now he has 604 cubes of fun, our engine builder just had to happen have a new dart block, jesel belt drive, 55 mm roller cam, and jesel .904 lifters for sale that another customer bought new but changed directions so it was purchased for song! Filling it out was callies pro mangnum crank and rods, afr 385 heads (with extra work done) , jesel rockers and marcella sheet metal intake with two gary williams dominators, weaver bros extnal oil pump, stephs pan, moroso vacum pump set up. Am in the process of mounting front motor accessories and will be on the dyno when finished, will post results later.

Since the motor was getting beefed up, Jack at mpd was called to go thru the boat and make more upgrades, set back, low pro intake, jetaway, go thru entire pump again, with new imp, inducer, custom loader grate and remount the engine. Jack was nice enough to bring the boat to the burley race for delivery!

Next, new gauges, wiring, upholstery and carpet, so yes, a new set of heads and we are here now, HA!! will post new pick as they come, thanks
 

Attachments

·
Registered
Joined
·
6,573 Posts
What a waste of a beautiful motor....just sayin...:cowdodo:
mr. can, you should waddle back over to the fluff n buff section where everything is about which new wax product is in vogue. :). or, how to find 7*. this is a no bs kick ass deal that will chew up and spit out anything you got for a tuesday night deal. PLUS it will be yet another full on chic magnet at those tuesday night deals, as verified by all the pictures that have been posted time and time again. chics dig jets. obviously, lolyfe and kettle know something you don't... :)

bitchin deal guys. will haul ass.
 

·
"BOATLESS"
Joined
·
3,468 Posts
Very nice looking motor, 604ci!! In a setup CP should run hard!:)devil
What's the deal with the $10 valve covers though?
Let's see pic of the CP.
 

·
Premium Member
Joined
·
762 Posts
Discussion Starter #9
Very nice looking motor, 604ci!! In a setup CP should run hard!:)devil
What's the deal with the $10 valve covers though?
Let's see pic of the CP.
Glad you noticed those nice chrome morosos!! New valve covers are in box still, wont put them on until after the dyno session is over. Just trying to keep them looking nice till engine builder is done looking for any more hp!
 

·
Lookout I'm Crankin it Baby
Joined
·
6,576 Posts
mr. can, you should waddle back over to the fluff n buff section where everything is about which new wax product is in vogue. :). or, how to find 7*. this is a no bs kick ass deal that will chew up and spit out anything you got for a tuesday night deal. PLUS it will be yet another full on chic magnet at those tuesday night deals, as verified by all the pictures that have been posted time and time again. chics dig jets. obviously, lolyfe and kettle know something you don't... :)

bitchin deal guys. will haul ass.
You dead on..I hate to say..already "chewed up and spit out" the driver once...he tried to turn the beast at speed...aparently you can't turn these go fast jets...oooooooops...see ya..

And Lolyfe and Kettle1 do have all the chics...trouble is...they're 17...bwwwaahahahaaaaaa
 

·
Registered
Joined
·
2 Posts
That was driver error!

My little mishap where I got wet a couple years ago was a result of my stupidity and had nothing to do with the fine jet craft! A couple broken ribs later, I'm a much better pilot these days! :)

I'm a little throttle happy so I'm hoping I don't do anything stupid with 850+ hp behind me! Remember kids, safety first!:)hand
 

·
Registered
Joined
·
6,573 Posts
You dead on..I hate to say..already "chewed up and spit out" the driver once...he tried to turn the beast at speed...aparently you can't turn these go fast jets...oooooooops...see ya..

And Lolyfe and Kettle1 do have all the chics...trouble is...they're 17...bwwwaahahahaaaaaa
sure you can! just takes boating knowledge and skillz beyond yer understandingt:wink2:

thing is, wimmen and boats all get a bit older, one year at a time... no matter what, this think'll be quicker than anything else you got... BWAAAAAAA HAAAAAAAAAAaaaaaaa.
 

·
Registered
Joined
·
109 Posts
sure you can! just takes boating knowledge and skillz beyond yer understandingt:wink2:

thing is, wimmen and boats all get a bit older, one year at a time... no matter what, this think'll be quicker than anything else you got... BWAAAAAAA HAAAAAAAAAAaaaaaaa.
Don't let rcl fool u he's a closet jet boater at heart he's Gona have to let the cat outa the bag sooner or later . Why do you think there's so many of them at his little pow wows its not cuz he doesn't like them.
 

·
Registered
Joined
·
6,573 Posts
Don't let rcl fool u he's a closet jet boater at heart he's Gona have to let the cat outa the bag sooner or later . Why do you think there's so many of them at his little pow wows its not cuz he doesn't like them.
hhmmmm. classic case of jetboat envy... seen it many times... :)devil
 

·
Premium Member
Joined
·
762 Posts
Discussion Starter #15
A few pics of some progress, got most of the front accessories mounted, built a fuel pump vacuum pump port that goes thru motor plate for clean routing of hose, had to come up with a manifold system for water exiting manifold (just about done, still in mock up). Cut the tanks out to install bigger pickups and returns for new fuel system and reinstalled. Had to make some new carb
linkage pieces to clear manifold, Motor plates will be polished after the dyno session, making a carb mounting plate for scoop, will have more pics soon,
 

Attachments

·
Registered
Joined
·
1,608 Posts
Damn Tim!!! Bad ass set up....... Seems like 850 should just be scratching the surface with that thing. Can't wait to see the pics once it's all set up and installed.
 

·
Premium Member
Joined
·
762 Posts
Discussion Starter #20
Thanks for the kind words! Marcella's manifolds are pieces of art for sure ! I can look at it for hours and just wonder how he can lay those beads down around corners and other obstacles too, plus they make great power. Will post some pics of one that he is finishing up right now for my old man's street rod when we have it in hand., Braswell did the carbs, it is over the top!!!
 
1 - 20 of 34 Posts
Top