Performance Boats Forum banner

Status
Not open for further replies.
1 - 20 of 23 Posts

·
Registered
Joined
·
19,804 Posts
Discussion Starter #1 (Edited)
C500.....$500 REDUCED COMES WITH XTRA SET OF CASES ​...SOLD
PM ME
Z-DRIVE .....$700 REDUCED
make offer

HULLCRAFT....$200 ..........sold

used cases 10* 12* c500 ..........$100 ALL .sold

caps

caps w/tach drives SOLD

in/out cases and handles IN OUT CASES SOLD HAVE A FEW NEW

used mid plates for casale

 

·
Registered
Joined
·
794 Posts
C 500 Ratio?

Hey Mouze, do you happen to know what the ratio is in that C 500 gear case?
 

·
"The" masheenist
Joined
·
5,444 Posts

·
Registered
Joined
·
19,804 Posts
Discussion Starter #7
10 turns was 32 ...........so 5 would b 16
 

·
Or Seth, either one
Joined
·
3,270 Posts
10 turns was 32 ...........so 5 would b 16
Ummm :notsure:

Wouldn't those #'s indicate 320% OD?

10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

Whatever you guys are smoking... must be good shit :smoking-cannabis-03 hahaha

I must be missing some sort of inside joke. You guys know your shit.
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #9 (Edited)
hahahahahahahah not 30 turn :duh: 13 :grin:
 

·
"The" masheenist
Joined
·
5,444 Posts
Ummm :notsure:

Wouldn't those #'s indicate 320% OD?

10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

Whatever you guys are smoking... must be good shit :smoking-cannabis-03 hahaha

I must be missing some sort of inside joke. You guys know your shit.
I was just doing mathematical calc based on the numbers. Figured 5 turns of the top to 16 turns of the bottom makes .32. I was reprimanded already.

Obviously I was way off. :)

Brian
 

·
"The" masheenist
Joined
·
5,444 Posts
If I had it in front of me I could figure it out...I think.

Isnt this right?

Mark the top and bottom shafts. Rotate the top shaft and counting the turns of each shaft until the top and bottom shafts line up again.

In UCH, the input shaft turns 25 rotations and the output shaft turns 24 times until they both line up again, 24/25 is .96 underdriven.

I guess I will go sit back down and wait for the smart kids to speak up. :)

Brian

Ummm :notsure:

Wouldn't those #'s indicate 320% OD?

10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

Whatever you guys are smoking... must be good shit :smoking-cannabis-03 hahaha

I must be missing some sort of inside joke. You guys know your shit.
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #12
:hmmm::popcorn::coffee-n-news:
 

·
Registered
Joined
·
80 Posts
wsuwrhr is correct. if 10 turns on top shaft equals 32 turns on prop shaft it is 320% overdrive. Pretty unlikely. Better check again. Measure twice Cut once.
 

·
"The" masheenist
Joined
·
5,444 Posts
wsuwrhr is correct. if 10 turns on top shaft equals 32 turns on prop shaft it is 320% overdrive. Pretty unlikely. Better check again. Measure twice Cut once.
My Bad.

Mouser came by today for me to look over the billet cases and figure out how many 8 and 10 degs cases he has and I asked him to bring the C500 as well so I could redeem myself.

We rotated the top shaft 3 revs and the bottom rotated 4 revs, so she has a 32% overdrive in her.
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #15
PRICE REDUCTION...NEED GONE 3 DRIVES CMON.........:thumb:
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #16
Weekly bump
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #17
pm me any offers
 

·
Registered
Joined
·
199 Posts
Hall Craft V-drive ratio

Hi Mouzer, do you have an estimate on the Hall Craft gearing, & shaft sizes, Thanks..Skidder:wink2:
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #19
get that for ya tomorrow barried behind boat.......
 

·
Registered
Joined
·
19,804 Posts
Discussion Starter #20
sold the hull craft still have the Z-dRIVE $400
 
1 - 20 of 23 Posts
Status
Not open for further replies.
Top